Poulan 3300 User Manual download pdf (Page 5)

OPERATE YOUR SAW SAFELY

1. Do not operate a chain saw that is damaged, im

properly adjusted, or not completely and securely

assembled.

2. Operate the chain saw only in outdoor areas.

3. Do not operate the saw from a ladder or in a tree.

4. Position all parts of your body to the left of cut and

away from the saw chain when the engine Is

running.

5. Cut wood only. Do not cut metal, plastics, masonry, non

wood building materials, etc. Do not useyoursaw to pry or

shove away limbs, roots or other objects,

6. Make sure the chain will not make contact with any

object while starting the engine. Never try to start the

saw when the guide bar is in a cut or kerf.

7. Use extreme caution when cutting small size brush

and saplings. Slender material can catch the saw

chain and be whipped toward you or pull you off

balance.

8. Be alert for springback when cutting a limb that is

under tension so you will not be struck by the limb or

saw when the tension in the wood fibers is released.

9. Do not put pressure on the saw at the end of a cut.

This can cause you to lose control when the cut is

completed.

10. Stop the engine before setting the saw down.

MAINTAIN YOUR SAW IN GOOD

WORKING ORDER

1. Have all chain saw service performed by a qualified

service dealer with the exception of the items listed

in the maintenance section of this manual. For

example, if improper tools are used to remove or hold

the flywheel when servicing the clutch, structural

damage to the flywheel can occur and cause the

flywheel to burst.

2. Keep fuel and oil caps, screws and fasteners

securely tightened.

3. Keep the handles dry, clean, and free of oil or fuel

mixture.

4. Make certain the saw chain stops moving when the

throttle trigger Is released. For correction, refer to “Car

buretor Adjustments."

5. Stop the saw if the chain strikes a foreign object. 1 n-

sped the unit and repair or replace parts as necessary,

6. Disconnect the spark plug before performing any

maintenance except for carburetor adjustments.

7. Never modify your saw In any way. Use only attach

ments supplied or specifically recommended by the

manufadurer.

8. Always replace the handguard immediately if It

becomes damaged, or broken or is otherwise

removed.

9. Keep the vibration isolators in good condition.

Periodically insped isolators for tears, rips or separation of

the rubber portion from the metal mountings. Have a

qualified service dealer replace the isolators if worn or

damaged, ifvibration increases or if mounts develop an out

of round or swollen shape from exposure to gasoline and/br

oil. It is recommended that all isolators be replaced when

a failure to one occurs.

CARRY AND STORE YOUR SAW SAFELY

1. Handcarrythesawwiththeenginestopped.themuf-

fler away from your body, and the guide bar and chain

to the rear covered preferably with a scabbard.

2. Before transporting in any vehicle or storing in any

enclosure, allow your saw to cool completely, cover

the bar and chain and properly secure to avoid

turnover, fuel spillage or damage.

3. Empty the fuel tank before Storing the tool. Use

up fuel left in the carburetor by starting the eng

ine and letting the engine run until it stops.

4. Store in a dry area out of the reach of children and

away from'where fuel vapors can reach sparks or an

open flame from hot water heaters, eledrtc motors or swit

ches, furnaces, etc.

SAVE THESE INSTRUCTIONS

NOTE: Exposure to vibrations through prolonged use of

chain saws may produce WhItefinger disease

(Raynaud’s phenomenon). This phenomenon

reduces the hand’s ability to feel and regulate

temperature, produces numbness and burning

sensations and can cause nerve and circulation

damage and tissue necrosis.

An anti-vibration system designed to reduce

engine vibration is recommended for those using

chain saws on a regular or sustained basis and is

provided on this saw. However, an antivibration

system does not guarantee the avoidance of

Whitefinger disease. Continual and regular users

must monitor closely their use of chain saws and

physical condition.

Notice: Refer to the Code of Federal Regulations, Section

1910,266(5); 2.5.1 of American National Standard

Safety Requirements for Puipwood Logging, ANSI

03.T1978; and relevant state safety codes when

using a chain saw for logging purposes.

1 2 3 4 5 6 7 8 9 10 ... 23 24

Comments to this Manuals

No comments

Poulan 3300 User Manual Page 5

Comments to this Manuals

Related products and manuals for Petrol tool Poulan 3300